If you’re fitting a SWaP-optimized rugged computer into a vehicle or platform, check the power and heat budget before you pick the box. The MILPC-SWaP’s listed 40 watts is a calculated maximum, and its typical draw is still to be published. Its supply window and its lack of power hold-up decide how it rides through a short loss of input. And a sealed, passively cooled box can only shed the heat of its processor class.
Skip those checks and the cost shows up late. A box that doesn’t fit the platform’s power or heat budget, that resets on a dropout, or that lacks the ports the job needs means a redesign. You redo the mount and the supply after the platform is wired. Then you place a second order, and the schedule slips.
Three Sealed MILPC Computers Side by Side
Put the three sealed MILPC units in one view first. They trade box volume against cooling and compute. Line them up before you compare watts or degrees.
| Unit | Size (W x D x H) | Cooling | Input | Compute | Listed operating temperature |
|---|---|---|---|---|---|
| MILPC-SWaP | 6.00 x 5.10 x 2.00 in (base system, no connectors) | Passive, natural convection | 28 VDC nominal, 20 to 33 VDC | COM Express Type 10 module up to 15 W TDP, 8 GB memory | -40 to +75 C (confirm how it is defined) |
| MILPC-3200 | 6.75 x 6.75 x 4.00 in | Forced air with an integrated external cooling unit | 28 VDC nominal, isolated | AI module with 32 GB memory | -40 to +71 C |
| MILPC-4000 | 8.5 x 13.25 x 5.1 in | Passive conduction cooling | 18 to 36 VDC (28 VDC nominal), filtered | Quad-core processor with a graphics card option, up to 48 GB memory | -40 to +60 C |
Weight isn’t published for any of the three, so confirm the weight with Seatronx before you rate the mount. You can compare the full line on Seatronx’s military computers page. The MILPC-SWaP also calls out MIL-STD-810H for shock and vibration and MIL-STD-461G for EMI/EMC.
Read the input column closely. The MILPC-SWaP lists 20 to 33 VDC, and the MILPC-4000 lists 18 to 36 VDC. The MILPC-3200 lists 28 VDC nominal through an isolated supply, with no power hold-up, so ask for its range if your bus swings. Treat the temperature column with care, too. Each figure is a listed operating range, and the three may not be defined the same way.
Start With the 28 VDC Input and the 40 Watt Figure
The MILPC-SWaP takes 28 VDC nominal power through an isolated DC/DC supply. It has a single wide input range of 20 to 33 VDC. It calls out MIL-STD-1275E and MIL-STD-704F, with no power hold-up.
That last part is easy to miss. As a general principle, a computer with no hold-up has no stored energy to carry it through a brief loss of input. If the supply drops out for a moment, the box can drop with it. Ask Seatronx what the MILPC-SWaP does in a dropout. Then plan for a restart in the platform’s software, so a reset doesn’t cost you data.
Next, check the window against your bus. The Defense Department’s record for MIL-STD-1275 scopes that standard to the operating voltage limits and transients of 28 VDC power. That’s power at the input terminals of equipment on military ground vehicle platforms. Hold your platform’s own limits and transients up against the 20 to 33 VDC window. If a requirement has to name a standard and revision, settle that with Seatronx’s guide to MIL-STD-1275 and MIL-STD-704 on a rugged computer.
Then the 40 watts. It’s a calculated maximum for the whole system. The system’s typical and maximum power figures are still to be published. So budget on the maximum.
As a general rule, size the supply, the wiring and the generator or battery margin from the maximum figure, then confirm the typical one. Ask Seatronx for the typical figure before you lock those numbers in. A budget built on a hoped-for typical draw can leave the platform short when the box runs hard.
Heat: What a Sealed Passive Box Can Shed
On a SWaP-optimized rugged computer, heat is the budget you can’t see on a wiring diagram. The MILPC-SWaP is O-ring sealed for IP66 and cooled by natural convection. There’s no fan. There’s no air path through the box. The processor module can be up to 15 W TDP, and the 40 watt calculated maximum covers the whole system.
As a general principle, every watt the box draws ends up as heat. The case has to hand that heat to the air or the mount around it. So a box in a closed, hot compartment has less margin than the same box on open metal. Expansion cards can add their own heat inside the same sealed case. Pick the mount location with that in mind.
The listed operating range is -40 to +75 C. That figure carries an asterisk with no footnote. Ask Seatronx how it’s defined. Ask which processor module and which expansion cards it was tested with. Then compare the answer with the hottest air your compartment can reach with the platform running.
The listed storage range is -40 to +85 C. That’s for the box when it isn’t running, so don’t use it to size a hot compartment.
I/O and Expansion: What the Small Box Carries
The base I/O is two RS-232/485 serial ports, two GbE, six USB 2.0, one DisplayPort and one HD audio output. It comes out on MIL-DTL-38999 connectors, and expansion may use alternate rugged connectors. The box runs Windows and Linux 64-bit with 8 GB memory.
Expansion takes up to two half-length mPCIe cards or one full-length mPCIe card. Options include mSATA, GbE, video input, CAN and ARINC.
So CAN and video input are expansion options, not base I/O. That changes how you count. List every sensor and bus on the platform first. Then count ports. Each card you add uses up a slot. As a general rule, count it as extra size and extra heat too.
Some processor modules carry 32 GB of onboard storage, which isn’t removable, so confirm it for your configuration. An mSATA option goes up to 1 TB. A 2.5 inch SSD through the expansion slice goes up to 4 TB, with a FIPS 140-2 option.
One more catch. The 6.00 x 5.10 x 2.00 inch size is the base system, without connectors. Ask for the size with the expansion slice fitted before you draw the mount. Leave room for the mating connectors and cable bends as well.
When a SWaP Box Is the Wrong Pick
A SWaP-optimized rugged computer trades headroom for space. Some jobs need the headroom more.
AI inference is one. The MILPC-3200 carries an AI module with 32 GB memory. Its I/O includes two CAN 2.0, two GbE, two USB 2.0 and four RS-232/422/485 ports. It’s 6.75 x 6.75 x 4.00 inches and cools by forced air through an integrated external cooling unit. Accelerator load can add heat and cut into your operating-range margin. Seatronx’s guide to what adding AI costs a military-grade rugged server walks through that cost.
Graphics and video capture point to a bigger box. So does a need for more memory. The MILPC-4000 carries a quad-core processor with a graphics card option and up to 48 GB memory. It takes up to two removable 2.5 inch SSDs and has options for video capture and encode. It’s 8.5 x 13.25 x 5.1 inches and passive conduction cooled. It runs from an 18 to 36 VDC filtered input. Its listed operating range is -40 to +60 C.
Moving up costs volume. On the MILPC-3200, it also costs a fan path, so plan where the air comes in and goes out. The MILPC-4000’s listed +60 C sits below the MILPC-SWaP’s listed +75 C. Ask how each figure is defined before you treat that gap as a real difference.
A SWaP box is also the wrong pick in two plainer cases. One is a platform whose supply can’t stay inside 20 to 33 VDC. The other is a job that needs more than six USB 2.0 ports or more than two GbE ports before you add cards.
Choose by Platform
Choose the MILPC-SWaP if box volume is your hard limit and your 28 VDC supply stays inside 20 to 33 VDC. It suits a job that its base I/O plus one or two mPCIe cards can cover. Seatronx’s MILPC-SWaP is a 6 by 5 by 2 inch sealed, passively cooled rugged computer built on a COM Express Type 10 module that runs from 28 VDC nominal power with a calculated maximum of about 40 watts. Check the expansion options on Seatronx’s MILPC-SWaP page before you lock the mount.
Choose the MILPC-3200 if the job runs AI inference and needs CAN 2.0 on the base box. Give it room for 6.75 x 6.75 x 4.00 inches and a forced-air path.
Choose the MILPC-4000 if you need a graphics card, video capture and encode, or up to 48 GB memory. You’ll need room for 8.5 x 13.25 x 5.1 inches. You’ll also trade the MILPC-SWaP’s listed +75 C for a listed -40 to +60 C range. Plan the mount with its conduction-cooled heat in mind.
Questions to Send Before You Order a SWaP-Optimized Rugged Computer
Send these to Seatronx before the platform drawings are final.
- The typical power draw, to set beside the 40 watt calculated maximum.
- The weight of the unit as you’ll install it.
- What the box does in a dropout, given no power hold-up.
- How the -40 to +75 C operating figure is defined, and with which processor module.
- The size with the expansion slice fitted.
- Which expansion cards carry your CAN or video input.
- Whether your platform’s supply and transients stay inside the 20 to 33 VDC window.
Once you have the list, send Seatronx your platform’s power budget and the I/O you need.