Before you cut the console panel for a panel mount trackball, settle three things. The first is the mount style. Studs and holes are different order codes. The second is the seal, which on the TSX50 comes with the switch choice. The third is the drawing for the exact order code you’ll buy. The cutout dimensions sit in that drawing, not in the product page text.
Get one of these wrong and it shows up late. A panel cut for the wrong mount style, or from the wrong drawing, means a re-cut or a replacement panel and a late console build. And a seal rating you assumed may not match the order code. Then the console may not carry the seal it was specified for.
Studs or Holes: Which Mount Style Does the Panel Need?
The panel needs the mount style of the exact order code you buy. Studs and holes aren’t two ways to fit one unit. They’re different order codes, and each one can call for different panel work. Pick the code first, then draw the panel. Changing from studs to holes after the cut can mean cutting again.
The TSX50 mounts from the front, with studs or with holes. TSX50F2 and TSX50F8 are the studs versions. TSX50N2 and TSX50N8 are the holes versions. Each code also comes in a black top plate version, and those codes end in BT1. The holes versions take countersunk M4 screws. The screws aren’t included, so add them to the parts list.
The TBE38 splits the same way. TBE38F0 is panel mount with studs. TBE38N0 is panel mount with holes.
The TPP-55A1A6 is a 6 inch touchpad. It mounts from the front on a metal bracket with four threaded fixing studs. Draw the panel around that bracket and its studs.
The E50-76A2AD is a single panel mount order code, and it fits into the back of the panel. The recommended panel is 5 mm metal with eight M4 x 20 mm threaded studs welded to its underside. The nuts and washers aren’t supplied, so add them to the parts list. Take the cutout from its panel mount drawing, and ask Seatronx if anything on that drawing is unclear.
What Studs and Holes Mean for the Panel
As a general rule, a studs unit sits on the front of the panel. Its studs pass through holes drilled in the panel, and nuts go on from behind. So you may need to reach behind the panel to fit it. A holes unit, in general, is screwed in from the front. Either way, you make the choice before the panel is cut, and it’s a different order code.
Does the Switch Choice Change the Seal?
On the TSX50, yes. The order code sets the switches, and the switches set the seal. The F2 and N2 codes carry IP65 pushbutton switches. The F8 and N8 codes carry IP68 short travel switches. If the console needs an IP68 TSX50, you’re choosing the short travel switches.
The two switches also differ in travel and life. Pushbutton switches have 1.3 mm of travel and a mechanical life of 1 million. Short travel switches have 0.5 mm of travel and a mechanical life of 3 million. Both have a 4 N force.
So don’t write a single rating for the TSX50 on the console spec. Write the order code. The rating follows from it.
The TBE38 and the E50-76A2AD are IP68. The TPP-55A1A6 touchpad is IP65. Its bracket has a rim around the glass edge for added protection and IP65 sealing capability.
The Seal Ring and the Panel Behind It
Every TSX50 panel mount type comes with a silicone sponge seal ring for sealing the unit into your panel or console. For the other units, ask Seatronx what seal comes with them.
A rating on a unit describes the unit. Whether the console seals also depends on the work around it. As a general rule, a gasket seals only against a panel that’s flat, in good condition and free of jagged edges, with the gasket seated all the way round. That’s how one maker of panel-mount HMIs puts it in its installation and wiring guide.
So put the panel finish on the same drawing as the cutout. Flatness and edge finish belong there, along with where the seal sits. And don’t treat a Seatronx rating as the rating of the finished console. It describes the unit you bolt in.
Where Do the Cutout Dimensions Come From?
They come from the drawing for the exact order code you’re buying, not from the product page text. An overall size or a weight isn’t a cutout. Find the drawing that matches your mount style and your code. Take the cutout from it, and give that same drawing to whoever cuts the panel.
The TSX50 has separate drawings for the studs version and the holes version. The unit is 100 x 116 x 50 mm overall and weighs 0.6 kg. Those numbers tell you how big the unit is, not how big the hole is. The desktop TSX50S8 has its own sheet, so keep it out of the panel file.
The TBE38 has drawings for studs and for holes, with tolerances of plus or minus 0.25 mm. An IGES or STEP model comes on request.
The E50 needs one extra check. One sheet covers two order codes: E50-76A31D for desktop and E50-76A2AD for panel mount. Each has its own drawing, with tolerances of plus or minus 0.2 mm. Make sure you take the panel mount drawing.
Ask Before the Panel Goes to the Shop
As a general rule, ask for the drawing, the 3D model and the seal that ships with the unit before the panel is released to the shop. If a 3D model matters to your console design, ask Seatronx whether one exists for the unit you’re specifying. A model can help you check fit. The cutout still comes from the drawing.
Four Panel Mount Pointing Devices Side by Side
The four units differ in pointer, mounting and seal. You can browse the trackballs on Seatronx’s industrial trackballs page.
| Unit | Pointer | Mounting | Seal | Operating temperature |
|---|---|---|---|---|
| TSX50 | 50 mm ball. | Front mount, studs or holes. | IP65 or IP68 by switch choice. | -10 to +60 C. |
| TBE38 | 38 mm ball with scroll wheel. | Studs (TBE38F0) or holes (TBE38N0), any mounting angle. | IP68. | 0 to +55 C. |
| E50-76A2AD | 50 mm ball with scroll wheel. | Panel mount, one order code (backlit and anti-vibration options on request). | IP68. | 0 to +55 C. |
| TPP-55A1A6 | 6 inch touchpad with 8 shortcut keys (130 x 80 mm active area). | Front mount on a bracket with four threaded fixing studs. | IP65. | 0 to 70 C. |
The temperatures are operating ranges.
Choose by Console
All four are separate pointers that fix into the panel. If you’re still weighing a pointer built into the keyboard against a separate one, Seatronx’s guide to a keyboard with a built-in trackball or a separate pointing device covers that choice.
Choose the TSX50 if the console is stainless steel or the unit sits in a salty or greasy environment. It comes in blank stainless or with a black coated top plate, the BT1 codes. Seatronx’s TSX50 is a 50 mm panel mount trackball with a stainless steel carrier that mounts from the front on studs or through holes, and takes IP65 pushbutton or IP68 short travel switches. You can compare all eight versions on Seatronx’s TSX50 page. If the unit will get wet, look at the IP68 codes, F8 and N8. It’s vandal proof, and the top ring comes off so you can clean the ball and its compartment.
Choose the TBE38 if a 38 mm ball and a scroll wheel suit the operator, and the unit has to sit at an angle on a sloped console. Its mounting position is all angles. It has an integrated hall-effect scroll wheel and left, middle and right switch functions. It has an aluminium base plate and weighs about 700 g. As a general rule, put the pointer where the operator’s hand rests, and check reach at the console’s slope.
Choose the E50-76A2AD if you want a 50 mm ball with a scroll wheel. It has an integrated hall-effect scroll wheel and three switch functions. Backlit and anti-vibration options come on request, alone or together. For marine consoles, the IEC 60945 variant is E50-76A2AD-M004. It carries a Certificate of Conformity fully compliant with IEC 60945. The TSX50 also comes in a marine range fully tested to IEC 60945, with order codes ending in -MC3. Ask Seatronx for the exact marine code and its IEC 60945 paperwork. For background on marine consoles, see Seatronx’s guide to why a vessel bridge needs an industrial trackball.
Choose the TPP-55A1A6 if a flat, solid-state pointer fits the console better than a ball. It’s a capacitive touchpad under a glass overlay, with no moving parts. Eight capacitive shortcut keys include a panel lock for cleaning or decontamination. Output is USB, and the 1.6 m USB cable is an optional accessory, so put it on the order. The module is 148.4 x 114.4 x 6.2 mm and weighs about 350 g. That’s still not a cutout.
Frequently Asked Questions
Does a panel mount trackball come with a seal ring?
The TSX50 does. Every TSX50 panel mount type comes with a silicone sponge seal ring for sealing the unit into your panel or console. For the TBE38, the E50-76A2AD or the TPP-55A1A6 touchpad, ask Seatronx what seal comes with the unit. Settle that before you draw the panel, so the seal is on the drawing.
Can the TBE38 sit at an angle on a sloped console?
Yes. The TBE38’s mounting position is all angles, so it can go on a flat or a sloped console. It comes as TBE38F0 with studs or TBE38N0 with holes. Pick the code, then take the cutout from the drawing for that code. Check the operator’s reach at the console’s slope before you fix the position.
Which interfaces do these trackballs use?
The TSX50 has a PS/2 and USB combo output on a shielded straight 1.6 m cable. The cable ends in a USB type A plug, with a PS/2 adaptor added, and it needs no special driver. Test the PS/2 port on the final PC configuration and operating system before installing in series. The TBE38 and the E50-76A2AD auto-select USB or PS/2, each with a USB A connector on a 2 m cable.
Is there a marine version with IEC 60945?
The E50-76A2AD and the TSX50 both have one. The E50’s marine variant is E50-76A2AD-M004, and it carries a Certificate of Conformity fully compliant with IEC 60945. The TSX50 also comes in a marine range fully tested to IEC 60945, with order codes ending in -MC3; ask Seatronx for the exact code and its IEC 60945 paperwork. Use the marine code when you ask for the drawing, so the panel is drawn for the unit you’ll order.
Can you get a 3D model for the console design?
For the TBE38 and the TPP-55A1A6 touchpad, yes. The TBE38 has an IGES or STEP model on request, and the touchpad has a STEP model on request. For the TSX50 and the E50-76A2AD, ask Seatronx whether a 3D model exists for the exact order code. Either way, take the cutout from the drawing for that code. Use the model to check fit, not to set the cutout.
Questions to Settle Before You Cut a Panel for a Panel Mount Trackball
Run through this list before the panel drawing goes to the shop.
- Pick the mount style, studs or holes, and the order code that goes with it.
- On a TSX50, pick the switches, since they set IP65 or IP68.
- Pick the pointer: a 38 mm ball, a 50 mm ball or a touchpad.
- Get the drawing for that exact order code, and check that it’s the panel mount drawing.
- Take the cutout from that drawing, not from a web page or an overall size.
- Put the panel finish and the seal position on the same drawing as the cutout.
- Ask what seal ships with the unit and whether a 3D model exists.
If any line is still open, send Seatronx your panel drawing and the order code you are considering.